Tweezers LAB

Assemblies: force detector

 

force detector

Type Assembly
Drawing
Drawing (4.8 Kb)
Pictures
Picture
A) Mechanical parts only

A) Mechanical parts only
Picture
B) Mechanical parts assembled

B) Mechanical parts assembled
Picture
C) Circuit boards and cables
This is a picture of the detector with the DL-10 detector with its window removed and soldered in place.

C) Circuit boards and cables
Picture
D) PSD Holder with 2 detector boards
Shown is the DL-10 detector with window removed. To learn how to remove it, see "How to: Remove the window cover from the DL-10 detector" under Documents. Make sure to solder the detector in the proper orientation in accordance with the picture.

D) PSD Holder with 2 detector boards
Picture
E) PSD Holder with assembled boards

E) PSD Holder with assembled boards
Picture
F) Detector assembly with beamsplitter cube
Non-polarizing beamsplitter cube inserted with slope toward PSD detector so reflected light goes to PSD and transmitted light goes to Iris detector (PIN 10-DI). Cube held in place with plastic-tip set screw. Get set screws from Thorlabs KM05 mirror mount where they will not be used.

F) Detector assembly with beamsplitter cube
Picture
G) Cube in place
Looking from this view one sees PSD and Iris detectors superposed due to half-silvered mirror.

G) Cube in place
Picture
H) Piece of tape blocks stray light

H) Piece of tape blocks stray light
Picture
I) Complete detector assy on bracket

I) Complete detector assy on bracket
Picture
J) Bullseye filter setup
One detector needs one bullseye filter, one disk and a cut piece of tape with 0.5" diameter hole

J) Bullseye filter setup
Picture
K) Insert the bullseye filter centered on the detector and then put the disk over

K) Insert the bullseye filter centered on the detector and then put the disk over
Picture
M) Seal the detector with tape and trim off the border

M) Seal the detector with tape and trim off the border
Parents
Parts
NameManufacturerVendorRequiredStockCost
Bullseye filter, 8 mmcustom shopVarious machine shops1$20.00
Cable, 6 cond Belden 9536Allied Electronics6 ft$0.52
Connector, 8 pos double-row plugMolex 22-55-2081DigiKey1$0.83
crossbar bracketcustom shopVarious machine shops2$40.00
crossbar slidercustom shopVarious machine shops1$45.00
detector cross barcustom shopVarious machine shops1$50.00
filter holder disccustom shopVarious machine shops1$10.00
Hybrid beamsplitterNT49-005Edmund Optics1$175.00
Knob for #6 capScrewMcMaster Carr2$0.12
PC Board Detectors @4 boardsVarious board manufacturers0.2$59.50
Photo-diodePIN-10DIOSI Optoelectronics1$50.00
PSD holdercustom shopVarious machine shops1$125.00
PSD holder handlecustom shopVarious machine shops1$15.00
PSD largeDL-10OSI Optoelectronics1$195.00
Screw, SS Allen-cap4-40x3/8McMaster Carr2$0.04
Screw, SS Allen-cap8-32x3/4McMaster Carr2$0.08
Screw, SS Allen-cap8-32x5/8McMaster Carr1$0.07
Screw, SS Allen-cap4-40x1/2McMaster Carr6$0.05
Spacer, Brass1/4" long, 1/4" o.d., .115" i.d., non-threadedMcMaster Carr2$0.30
Terminal, crimpMolex 16-02-0104Newark7$0.12
WasherSS #8McMaster Carr1$0.07
Estimated cost: $783.22
 

List all the parts for "force detector"

last changed 2010/10/21 19:01