| | Picture | Title | Category | Assembly |
|---|
|
(1) ADC board on first layer
|
(1) ADC board on first layer |
boards |
Controller Board Stack
|
|
|
(2) ADC board on second layer
The same set of 3 boards as on thye first layer (ADC board and 2 preamplifier boards) except rotated 180 degrees. |
(2) ADC board on second layer |
boards |
Controller Board Stack
|
|
|
(3) Motor control board on third layer
|
(3) Motor control board on third layer |
boards |
Controller Board Stack
|
|
|
(4) Piezo control board on fourth layer
|
(4) Piezo control board on fourth layer |
boards |
Controller Board Stack
|
|
|
(5) Main control board on the fifth layer
|
(5) Main control board on the fifth layer |
boards |
Controller Board Stack
|
|
|
(6) Connect boards with ribbon cable
|
(6) Connect boards with ribbon cable |
boards |
Controller Board Stack
|
|
|
(8) Color code
Green = Force detector trap-A
Blue = Position detector trap-A |
(8) Color code |
boards |
Controller Board Stack
|
|
|
(9) more Color Codes
Yellow = Force detector trap-B
Red = Position detector trap-B |
(9) more Color Codes |
boards |
Controller Board Stack
|
|
|
Power connector, 3-wire
Black is ground; red is +5V; white is +12V. |
Power connector, 3-wire |
boards |
Controller Power Supply
|
|
|
Power connector, 4-wire
Brown is ground; orange is +15V; blue is -15V. The reason for 4 wires is to reduce confusion with connections if both were 3-wire. |
Power connector, 4-wire |
boards |
Controller Power Supply
|
|
|
Piezo control board
version 9 uses surface-mount amplifiers Apex PA340 |
Piezo control board |
boards |
Piezo driver board
|
|
|
Piezo_Driver 8
version 8 used Apex PA240 amplifiers |
Piezo_Driver 8 |
boards |
Piezo driver board
|
|
|
Laser Power Supply Board
side that faces away from front panel |
Laser Power Supply Board |
boards |
Laser Power Supply
|
|
|
Diode Driver Board Modified
Thorlabs IP 500 diode driver modified by soldering in wire harness. Remove trim pot "P/I ADJ" and solder 3 wires into holes.
Requires careful work with a "solder sucker".
The board is connected to a socket 16 through 12" ribbon cable. |
Diode Driver Board Modified |
boards |
Laser Power Supply
|
|
|
(7) Attach detector cables
Plug detector cables into 8-pin headers on Preamp Boards. Position connector with red wire and blank position on top. Be carefull not to plug it upside down or offset right/left by 1 pin. Such a mistake won't damage anything, but it won't work that way. |
(7) Attach detector cables |
boards |
Analog to Digital Converter Board
Controller Board Stack
|
|
|
ADC Mother board
Install 2 jumpers:
(1) from EOC (End Of Conversion) to ribbon wire 17
(2) from CS (Chip Select) to ribbon wire 15 |
ADC Mother board |
boards |
Analog to Digital Converter Board
|
|
|
ADC board with piggyback preamplifier boards
|
ADC board with piggyback preamplifier boards |
boards |
Analog to Digital Converter Board
|
|
|
board back side
|
board back side |
boards |
laser power supply circuit board
|
|
|
board front side
|
board front side |
boards |
laser power supply circuit board
|
|
|
Push button Modified
Bend tabs and solder wires that will feed through holes in PC board |
Push button Modified |
boards |
laser power supply circuit board
|
|
|
detector boards
|
detector boards |
boards |
|
|
|
motor limit board
Part of Detector Board set has been cut ouy |
motor limit board |
boards |
|
|
|
Preamp Board bottom
|
Preamp Board bottom |
boards |
Preamp board
|
|
|
Preamp Board side
|
Preamp Board side |
boards |
Preamp board
|
|
|
Preamp Board top
|
Preamp Board top |
boards |
Preamp board
|
|
|
Main control board
|
Main control board |
boards |
main control board
|
|
|
Motor control board
|
Motor control board |
boards |
Motor control board
|
