| | Picture | Title | Category | Assembly |
|---|
|
(C) Wrap with 1" black tape (Thorlabs T137-1.0) and cut two holes with scalpel (see description).
Larger hole is for the lower periscope, and the smaller hole is for the wrench to access the screw in the pick-off assembly for adjustment. |
(C) Wrap with 1" black tape (Thorlabs T137-1.0) and cut two holes with scalpel (see description). |
instrument assembly |
Lower optical train
|
|
|
(D) Reinstall position detector lower periscope.
|
(D) Reinstall position detector lower periscope. |
instrument assembly |
Lower optical train
|
|
|
Magnetic Lens Mount
magnetic ring is held by 3 rare-earth magnets which are glued into depressions (holes marked "F") in the Hexagon Base |
Magnetic Lens Mount |
instrument assembly |
CCD camera assembly
|
|
|
Dowel pins made from 1/8" Brass tube
Use same brass tube as in wiggler, cut to 1/2" length |
Dowel pins made from 1/8" Brass tube |
instrument assembly |
|
|
|
Press pins into holes using guide to keep them straight
Metal guide made from 1/4" thick scrap aluminum. Drill with #30 drill |
Press pins into holes using guide to keep them straight |
instrument assembly |
|
|
|
Motor Cable Clamp
where motor cable harness enters instrument head |
Motor Cable Clamp |
instrument assembly |
motor cable harness
|
|
|
Motor cable harness
|
Motor cable harness |
instrument assembly |
motor cable harness
|
|
|
Rear side of the main control board
Three capacitors are Panasonic ECJ-3VB1E334K |
Rear side of the main control board |
instrument assembly |
main control board
|
|
|
B) Laser Mount wiring
Wire connections to Laser Mount PC Board and on DB-9 connector. On the connector wire pins as follows:
Pin1=brown
Pin2=red
Pin3=orange
Pin4=yellow
Pin5=green
Pin6=blue (same end as pin1)
Pin7=violet
Pin8=black
Pin9=white (same end as pin5) |
B) Laser Mount wiring |
instrument assembly |
Laser assembly
|
|
|
C) Diode laser (Lumics) and laser base
Laser, base and circuit board with wires attached
Schottky diode protects Laser diode from static |
C) Diode laser (Lumics) and laser base |
instrument assembly |
Laser assembly
|
|
|
A) Base with circuit board
|
A) Base with circuit board |
instrument assembly |
Laser assembly
|
|
|
D) Unwind the optical fibre from the box
|
D) Unwind the optical fibre from the box |
instrument assembly |
Laser assembly
|
|
|
E) Fix the laser into the laser base
|
E) Fix the laser into the laser base |
instrument assembly |
Laser assembly
|
|
|
F) Wind the optical fibre inside the laser base clockwise
|
F) Wind the optical fibre inside the laser base clockwise |
instrument assembly |
Laser assembly
|
|
|
G) Feed the FC termination inside
FC termination goes through the hole on the laser base front, then it is fed through the feedthru plate into the adapter from ThorLabs with cap. |
G) Feed the FC termination inside |
instrument assembly |
Laser assembly
|
|
|
H) Fix the feedthru plate
|
H) Fix the feedthru plate |
instrument assembly |
Laser assembly
|
|
|
I) Place foam inside to keep the optical fibre in place
|
I) Place foam inside to keep the optical fibre in place |
instrument assembly |
Laser assembly
|
|
|
J) Ground soldering iron to the laser base
|
J) Ground soldering iron to the laser base |
instrument assembly |
Laser assembly
|
|
|
K) Solder the laser to the base
|
K) Solder the laser to the base |
instrument assembly |
Laser assembly
|
|
|
L) Cover the laser base and label with serial number
|
L) Cover the laser base and label with serial number |
instrument assembly |
Laser assembly
|
|
|
optical_layout
|
optical_layout |
instrument assembly |
|
